You lean back and the armchair squeaks. The next time you turn, it creaks. After a few weeks, the noise accompanies your every movement, and you start to wonder if the thing is broken. First, the good news: with recliners, a squeak is almost never a fault, but rather a dry or dirty sliding mechanism. In the vast majority of cases, you can sort it out yourself in twenty minutes, without a toolbox and without booking a service appointment.
Show table of contents
Summary/TLDR
Pin down the source by swivelling the chair, rocking it and standing up, whilst listening to where the creaking comes from. Three areas are responsible for around nine out of ten noises: the swivel base with its ball bearing ring, the slide bearings of the rocking mechanism, and the screw connections between the seat and the base. Treat these with a dry PTFE or silicone spray – not with penetrating oil and certainly not with cooking oil. Clean first, then apply sparingly, then move the chair. If the noise persists after tightening all the screws and applying lubricant, or if it sounds like metal grinding, it’s a job for the service department.
Why does a recliner squeak in the first place?
A recliner is a piece of furniture designed to move. It swivels, it rocks, it extends the backrest, and with each of these movements, components rub against one another. As long as there is a lubricating film between them, you won’t hear a thing. If this film disappears, stick-slip occurs: two surfaces stick together briefly, then come apart abruptly and start to vibrate. You hear this vibration as a squeak.
The lubricating film disappears for four reasons:
- Time. Factory grease dries out after two to five years or migrates out of the raceway.
- Dust. Fine house dust binds with the grease, turning it into an abrasive paste. Pet hair accelerates this process considerably.
- Dry, heated air. Wooden joints and leather upholstery expand and contract more in winter – which is why the problem typically starts during the heating season.
- Loose screws. A component with minimal play rubs against a surface it was never intended to touch.
Important to bear in mind: A squeak is a noise caused by friction. A crackling sound under load usually comes from a loose connection. A metallic grinding noise indicates a damaged ball cage. Only the third case is a genuine problem.
Pin down the source in five minutes
Before you spray anything, you need to know where to aim. To do this, work through the steps one by one and get someone to help you – with two people, you’ll find the spot much quicker, as one person moves the chair whilst the other listens.
- Rotate the armchair without rocking it. Sit down and slowly turn round on your own axis. If it squeaks here, the cause lies in the swivel base.
- Rock the chair without turning. Place one hand on the armrest and rock gently back and forth. If the noise comes only from here, it’s the rocking mechanism or the spring assembly.
- Stand up and sit down. A clicking sound at exactly this moment almost always comes from the screw connections between the seat pan and the base.
- Adjust the backrest. If the noise only occurs when adjusting it: the backrest hinge or – on models with a gas spring – its mounting.
- Move the chair whilst it’s empty. Stand up and move the empty chair by hand. If the noise persists, it’s the mechanism. If it disappears, it’s the cover or the upholstery – this is harmless and usually sorts itself out.
Make a note of the specific movement that causes the noise. This single piece of information will save you from spraying half the chair.
The most common cause: the turntable and swivel ring
In most recliners – including Stressless models and most replicas – the swivel base consists of a ball bearing between two metal rings. This is exactly where dust accumulates, and this is exactly where the grease dries out first.
Here’s how to do it:
- Tilt the armchair or lay it on its side. Do this with a partner, placing a blanket under the contact surface. For heavier models, it’s enough to tilt it just far enough to reach the ring.
- Clean the ring. First dry with a brush or hoover, then with a cloth and a little isopropyl alcohol. The old, hardened grease must be removed – applying new lubricant on top of old grime will only make matters worse.
- Lubricate sparingly. Apply PTFE spray or silicone spray to the raceway, not to the visible surfaces. A quick spray all round is enough.
- Distribute it. Set up the chair, sit down, and make twenty to thirty full revolutions in both directions. This distributes the lubricant across the entire ring.
- Wipe off any excess. Any residue on the outside will attract dust.
The noise will usually disappear afterwards. If it returns after a few days, the ball cage is worn out and needs replacing – a spare part that most manufacturers stock separately.
What to use for lubrication – and what definitely not to use
| Lubricant | Suitable for | Rating |
|---|---|---|
| PTFE spray (Teflon) | Slewing ring, metal plain bearings, hinges | First choice. Dries to a dry film and therefore attracts hardly any dust. |
| Silicone spray | Plastic glides, rubber bearings, textile contact points | Very good, particularly where plastic slides on metal. Does not damage upholstery. |
| White lithium grease | Heavily loaded metal joints | Useful, but apply only where needed with a brush – do not spray. |
| Penetrating oil (classic WD-40) | Only for loosening seized screws | Not a lubricant. It seeps into the upholstery, turns to resin and makes the problem worse within a few weeks. |
| Cooking oil, Vaseline, candle wax | — | Stay away from these. They go rancid, attract dust and leave stains on the upholstery. |
| Graphite powder | — | Works in theory, but will permanently stain any light-coloured upholstery. |
Basic rule: less is more. A half-second spray is enough for one sliding point. If you spray too generously, a week later you’ll have a dust trap and stains on the floor.
Before spraying, place an old towel under the area and cover any leather or fabric surfaces. Silicone is very difficult to remove from upholstery.
Tightening screws: the underestimated step
Before you reach for the spray, it’s almost always worth doing a quick check with an Allen key. On recliners, the following screws typically come loose:
- the four to six screws between the seat plate and the swivel base
- the connection between the base and the column
- the bolts in the backrest hinge
- the armrest fixings
Tighten them by hand – don’t use force. Over-tightened screws in wood or chipboard can tear out, and then the squeaking turns into real damage. If a screw can no longer be gripped, a longer bolt with a washer or a wooden dowel in the worn-out hole will help.
Another classic problem: the armchair isn’t level. On a slightly uneven wooden floor, the base twists with every movement, and this twisting causes a creaking sound. Place felt pads underneath and check whether the armchair wobbles – it costs nothing and solves more problems than you might think.
If the gas spring hisses or groans
Models with height adjustment or an adjustable backrest have a gas spring. A quiet hissing sound when adjusting the chair is normal – that’s the gas spring at work. What isn’t normal is:
- a groaning or creaking sound with every movement: this is usually caused by the spring’s bearings, not the spring itself. A drop of PTFE at the mounting points is sufficient.
- the seat sagging under load: the gas spring has lost pressure and needs replacing.
- Oil marks on the piston rod: the spring is leaking and needs replacing.
Gas springs are under high pressure. They must be replaced; they must not be opened, drilled into or disposed of with household waste.
When you should stop and call a service technician
Carrying out repairs yourself is almost always the right thing to do when noises occur. However, these signs should still be dealt with by a professional:
- A metallic grinding noise when turning – the ball ring is damaged.
- Noticeable play between the seat and the column that cannot be eliminated by tightening.
- Visible cracks in the base, welds or frame.
- The noise returns within a few days , even though the chair has been cleaned and lubricated.
- The chair is still under warranty. In this case, the rule is: contact the manufacturer first. Opening it yourself may invalidate your warranty.
If it is an electric massage chair rather than a mechanical recliner, the causes and procedures are different – motors, timing belts and roller tracks produce their own noises. We cover this in Massage chairs squeak. Everything you need to know about routine maintenance can be found in Maintenance of Massage Chairs, and ‘How loud is a massage chair?’ explains how to classify noise levels in general.
How to stop the noise from returning
- Tighten all screws once a year . It takes ten minutes, usually at the start of the heating season.
- Clean and re-lubricate the swivel base every two years .
- Vacuum under the chair regularly. Anything that doesn’t get into the track won’t need to be removed later.
- Do not let anything fall into the chair. The impact puts more strain on the ball bearing ring and screw connections than any normal use.
- Do not use the armrests as a seat. This is the most common cause of screws coming loose.
- Keep the chair away from the radiator. Direct heat dries out both the leather and the lubrication points.
Conclusion
A squeaky recliner is a maintenance issue, not a repair issue. Identify the source by turning, rocking and standing up; tighten all screws; clean the affected sliding part and apply PTFE or silicone spray sparingly. This will sort out most noises in under half an hour.
What you shouldn’t do: use penetrating oil, spray liberally or try to mask a metallic grinding noise. The first makes it worse, the second dirties the chair, and the third delays addressing a problem that could still be fixed cheaply with a spare part.
Frequently Asked Questions (FAQs)
What’s the best way to lubricate a recliner?
Use PTFE spray for metal-on-metal parts such as the swivel ring, and silicone spray for plastic glides and rubber bearings. Both dry to form a film and attract hardly any dust. Penetrating oil is intended for loosening screws, not for lubrication, and it hardens over time.
How do you lubricate the swivel ring of a recliner?
Carefully tilt the chair or, with the help of a second person, lay it on its side; first clean the ball bearing ring dry and then remove the old grease with isopropyl alcohol; apply a brief spray of PTFE to the raceway and then rotate the chair twenty to thirty times in both directions. Wipe off any excess so that it doesn’t attract dust.
Why does my armchair only creak when I stand up?
Because when the weight is taken off, the screw connections between the seat plate and the base move slightly. This is almost always due to a loose screw and can be fixed in a few minutes with an Allen key. Friction noises from the mechanism, on the other hand, occur whilst the chair is moving, not just at the end of the movement.
Can I spray WD-40 on my recliner?
Yes, to loosen a stuck screw; no, not as a lubricant. Standard WD-40 is a penetrating oil: it displaces moisture but does not remain in the guide rails; it seeps into the upholstery and cover and turns to resin. The squeaking will return after a few weeks, and the cover will have a stain.
Is a squeaky armchair dangerous?
Not usually. A rubbing noise is harmless. You should be wary of metallic grinding, noticeable play between the seat and the column, or visible cracks in the base – these are signs of mechanical damage, and in such cases the armchair should no longer be subjected to full weight until it has been inspected.
How often should you service a recliner?
Tighten the screws once a year, and clean and re-lubricate the swivel base every two years. If the chair is used daily, there are pets in the household, or it is placed on a carpet, it’s worth carrying out maintenance more frequently.




Leave a comment
This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.